Free Download passguide cisco ccna 640-802 v3.38 1 | Latest Cisco CCNA Certification Dumps

passguide cisco ccna 640-802 v3.38 1

By PassGuide CCNA Training Materials and Practice Tests | April 1, 2010

Question:434
IP addresses and routing for the network are configured as shown in the exhibit. The network administrator issues the show ip eigrp neighbors command from Router1 and receives the output shown below the topology. Which statement is true?

A. It is normal for Router1 to show one active neighbor at a time to prevent routing loops.
B. Routing is not completely configured on Router3.
C. The IP addresses are not configured properly on the Router1 and Router3 interfaces.
D. The no auto-summary command configured on the routers prevents Router1 and Router2 from
forming a neighbor relationship.

Answer: B

Question:435
Refer to the exhibit. The network administrator has discovered that the VLAN configuration of SwitchC is not synchronized with the rest of the switched network. Why is SwitchC not receiving VTP updates?

A. SwitchA supports a greater number of VLANs than does SwitchC.
B. SwitchC has fewer existing VLANs than does SwitchA.
C. SwitchC has a revision number higher than that being advertised.
D. SwitchC should be operating in VTP server mode to receive VTP updates.
E. SwitchB is not relaying VTP advertisements to SwitchC.
F. SwitchB should be operating in VTP server or client mode to relay VTP updates.

Answer: C

Question:436
Refer to the exhibit. A router interface is being configured for Frame Relay. However, as the exhibit
shows,the router will not accept the command to configure the LMI type. What is the problem?

A. The interface does not support Frame Relay connections.
B. The interface does not have an IP address assigned to it yet.
C. The interface requires that the no shutdown command be configured first.
D. The interface requires that the encapsulation frame-relay command be configured first.

Answer: D

Question:437
Refer to the exhibit. Two buildings on the San Jose campus of a small company must be connected to use Ethernet with a bandwidth of at least 100 Mbps. The company is concerned about possible problems from voltage potential differences between the two buildings. Which media type should be used for the connection?

A. UTP cable
B. STP cable
C. coaxial cable
D. fiber optic cable

Answer:D

Question:438
You are securing a network and want to apply an ACL (access control list) to an interface of a router.
Which one of the following commands would you use?

A. apply access-list 101 out
B. ip access-group 101 out
C. access-class 101 out
D. permit access-list 101 out

Answer: B

Question:439
How many subnets can be gained by subnetting 172.17.32.0/23 into a /27 mask, and how Many usable host addresses will there be per subnet?

A. 8 subnets, 31 hosts
B. 8 subnets, 32 hosts
C. 16 subnets, 30 hosts
D. A Class B address can’t be subnetted into the fourth octet.

Answer: C

Question:440
Refer to the exhibit. After SwitchB was added to the network, VLAN connectivity problems started to occur. What caused this problem?

A. Both switches are in server mode in the same domain.
B. The revision number of SwitchB was higher than the revision number of SwitchA.
C. SwitchA was not rebooted prior to adding SwitchB to the network.
D. V2-mode is not enabled.
E. VTP pruning is not activated, so the new paths in the network have not been recalculated.

Answer: B

Question:441
Refer to the exhibit. The output that is shown is generated at a switch. Which three of these
statements are true? (Choose three.)

A. All ports will be in a state of discarding, learning, or forwarding.
B. Thirty VLANs have been configured on this switch.
C. The bridge priority is lower than the default value for spanning tree.
D. All interfaces that are shown are on shared media.
E. All designated ports are in a forwarding state.
F. This switch must be the root bridge for all VLANs on this switch.

Answer: C, E, F